CASE STUDIES

The Pizza Project: A Wedge-Shaped Sofa Built From A Client’s Sketch

Cortina d’Ampezzo, Italy

Giulia came to us with a hand sketch of the sofa she wanted for a room with an awkward angled wall. We refined it into technical drawings and then handmade a custom Mah Jong sofa in her own chenille fabric. Its wedge-shaped “pizza” seat sits flush against the wall.

Custom Mah Jong sofa based off of a customer's sketch with a wedge-shaped seat that looks like a pizza slice

Project at a Glance

CLIENTS

Giulia

LOCATION

Cortina d’Ampezzo, Italy

Room

Ground-floor bunk room with an angled wall

Materials

Client’s own chenille upholstery fabric (COM)

Dimensions

About 117 × 77 in (297 × 195 cm)

Made

Custom and handcrafted

Investment

$6,580

What We Customized

Mah Jong sectional:

  • “Pizza” seat: A wedge-shaped seat and mat cut at 65° and 25°, so the sofa sits flush against the angled wall.
  • Pizza crust back: A back support angled to follow the wedge all the way to the wall.
  • Single seaters: Two 37.4 in (95 cm) seaters, sized to line up with the pizza seat.

Fabrics:

Giulia’s own chenille upholstery fabric (COM).

A Sketch to Start, and One Very Awkward Wall

Giulia knew exactly what she wanted, right down to the centimeter (we’d say inch, but she’s in Italy).

When Giulia first got in touch, she’d already drawn the sofa herself. Her hand sketches showed every seat, mat and back support, each one labeled and measured, for a room in Cortina d’Ampezzo, Italy.

The tricky part was the wall. It doesn’t meet the room at a neat right angle but runs off on a slant, so a regular sofa pushed against it would hit corner-first and leave an awkward gap.

Along with her sketches, she sent us a professional floor plan and her own fabric. What she asked of us was simple to say out loud: build the sofa she’d drawn, keep it low to the floor and make it sit flush against that wall.

THE ROOM’S RULES

  1. Follow Giulia’s hand-drawn sketch
  2. Sit flush against a slanted wall
  3. Stay low to the floor
  4. Use customer’s own chenille fabric
Technical drawing of a wedge-shaped sofa seat with 65° and 25° angles
Our technical drawing of Giulia’s sketch, with the 65° and 25° angles where the pizza seat meets the slanted wall.

Turning a Hand Sketch Into Something We Could Build

We kept refining her sketch until every angle matched her wall.

Giulia’s sketches were great, and it was clear she knew that room better than anyone. She’d marked where the seaters went, where the mats sat underneath and where the open floor began.

But what the sketch can’t tell you is the exact angle where a cushion meets a wall. On a wall like hers, being off by a few degrees leaves a gap you’d notice every time you walked in.

So we sat down with her floor plan as a team and worked it through. Our technical drawings put the wedge at 65° on one side and 25° on the other. From there we went back and forth with Giulia over several rounds.

Our first round followed her sketch closely, with 47.2 in (120 cm) seaters. Eventually, we settled together on 37.4 in (95 cm) seaters and a 42.2 in (107.3 cm) wedge.

Creating the Pizza Slice

Around our studio, we still call this one the Pizza Project.

The two square seaters sit side by side, but between them and the slanted wall there’s a triangle of floor no square seat can fill. A standard corner piece would either stick out into the room or leave empty floor behind it.

So we made the wedge from scratch. The seat and the mat underneath are cut to the angle of the wall and finish in a squared-off 7.9 in (20 cm) tip.

Look at it from above and it’s obvious where the nickname came from.

It’s a giant slice of pizza. And the back support looks just like a crust. 

It’s a silly name for a serious bit of geometry and customization. And we’re proud of it.

Why do we work out every angle before cutting any fabric?

A wedge only works if its angle matches the wall exactly. Over an edge about 3 ft (1 m) long, being two degrees off opens a gap of around 1.4 in (3.5 cm) at the far end. That’s why we draw every angle first and cut the pieces to the drawing.

Upholstering It in Giulia’s Own Fabric

Giulia brought her own chenille, and we made it work on every angle.

Most people start by ordering our 20 free fabric swatches, but Giulia had already found hers. It’s a chenille upholstery fabric in oatmeal, with little flecks of orange and gray that show up close.

Chenille is easy to work with on a square cushion. A wedge is a different story, because the fabric has to wrap a sharp angle and still sit neatly at the tip. It’s the kind of detail we pay close attention to whenever clients are using their own fabric (COM).

We tufted every seat and mat with buttons covered in the same chenille. Every piece also has removable covers that come off for cleaning.

The Result

Wood-paneled room with an angled wall and a sofa outline taped on the floor

BEFORE

Giulia’s room in Cortina d’Ampezzo, with the sofa’s outline marked in tape on the floor.

Low Mah Jong sofa in oatmeal chenille with a wedge-shaped seat

AFTER

The finished sofa with its pizza seat and angled crust, photographed in our studio.

The finished sofa looks just like Giulia’s sketch, and it sits flush against the wall.

The pizza seat meets the slanted wall at 65° and 25°, so there’s no gap to hide behind a pillow. The seaters, mats and back supports all sit where Giulia drew them, in the chenille she chose.

The sofa arrived with customs duties, tariffs and import taxes already included, so there were no surprise fees at the door.

And delivery wasn’t the end of it. Like with all our customers, we provide Giulia with lifetime support.

INCLUDED

Customs duties, tariffs and import taxes

AFTER DELIVERY

Lifetime support: product care and adding modules

Questions We Get About Projects Like This

We can make a sofa that fits an awkward room by designing every piece around the room’s real shape. Giulia’s room has a wall that runs off at an angle, so we built her sofa with a wedge-shaped “pizza” seat that fills the corner exactly.

We can make a Mah Jong sofa fit against a slanted wall by cutting a custom module to the wall’s exact angle. For Giulia, we cut the pizza seat and its mat at 65° and 25°, so the sofa sits flush against her wall with no gap.

We make sure a custom sofa fits an awkward space by working out every dimension and angle in technical drawings before we cut any fabric. Giulia sent us her hand sketch and floor plan, and we refined the drawings with her over several rounds until every piece lined up with her room.

Have a Room With Its Own Rules?

Reach us anytime at info@adorncroft.com, and we’ll design your dream home around you.

Bring this sofa home, in your colors.

Start from Brandye and Kirk’s Mah Jong sofa and make it fit your room.

Shop Their Piece

Start a conversation with our friendly team.

Our design team will guide you to create the furniture of your dreams.

Talk to Our Designers
Scroll to Top